October 24, 2026
Choosing flake colors and chip size for a Huntington garage floor
Four choices decide how a flake floor looks: the blend of chip colors, the chip size, how thickly the chips go down and the base color under them. Each one is worked through below from the flake and coating makers' own data sheets and guides.
Four choices behind the look of a flake floor
A flake floor is built in layers: a pigmented base coat, decorative chips, called flake, thrown into that coat while it is still wet, and a clear topcoat over the chips. What you see comes from four choices made in the first two layers: the blend of chip colors, the size of the chips, how thickly they are spread and the color of the base coat beneath them. Torginol, which makes decorative flake, offers more than 150 color-styles in six sizes and recommends a clear topcoat to encapsulate the chips and take the wear.
The slab matters to those choices. The median year built for the Town of Huntington's housing is 1963, according to the Census Bureau's 2020-2024 American Community Survey, so many garages here sit on old slabs, and old slabs tend to carry patches, filled cracks and stains. Laticrete's data sheet for its blended chip says the chips can help disguise small flaws in the concrete, one reason a full broadcast suits an older garage. The choice between flake and a solid-color garage floor comes before any of the four; this post assumes flake and takes the four in turn, as they apply to flake garage floors across the Town of Huntington.
Chip size: a quarter inch, an eighth or smaller
Torginol sells flake in six size profiles, from 1 inch down to 1/32 inch, and names 1/4 inch its most popular size. On the look, it says 1/32, 1/16 and 1/8 inch chips give a more natural, aggregate-like finish, while 1/4, 1/2 and 1 inch chips make bolder, more graphic patterns. Smaller chips also blur a blend: each color is harder to pick out and the floor reads as one even tone, and a neutral gray or brown blend starts to look like stone.
Smaller chips take more material to cover the same floor. For a full broadcast, Torginol's flake data sheet puts coverage at 5 to 7 square feet per pound for 1/4 and 1/8 inch flake and 3 to 5 square feet per pound for 1/16 and 1/32 inch. Laticrete's sheet gives 5 to 7, 4 to 6 and 3 to 5 square feet per pound for its 1/4, 1/8 and 1/16 inch chips. Torginol also sells hybrid blends made mostly of 1/16 inch chips with some 1/4 or 1/8 inch mixed in, which it says resemble polished concrete or terrazzo.
Full broadcast or a light scatter of chips
A full broadcast keeps throwing chips into the wet base coat until it will hold no more. Laticrete's blended chip data sheet calls for broadcasting to refusal, with no resin showing and no wet areas left. Once the coat cures, the loose chips are blown off and the floor is scraped with a metal floor scraper in three directions. The same sheet warns that a poor scrape leaves an uneven texture and uses up extra topcoat.
A partial broadcast scatters fewer chips, so more of the base coat stays in view and the base color makes up more of what the eye sees. Torginol's chart shows how far apart the two are: for 1/4 inch flake, a pound covers 5 to 7 square feet at full coverage, 25 to 50 at heavy coverage and 50 to 200 at light coverage. A light scatter saves flake, but it also gives up much of the texture that chips add to a floor and leaves less to disguise a patched slab. The garage floor coating page compares the epoxy and polyurea systems a broadcast can sit in with one-part paint and sealer.
Matching the base coat to the chip blend
Even a full broadcast leaves small gaps where the base coat peeks through, so its color tints the finished floor. Torginol's advice is to choose a base close in color and tone to the most prominent color in the blend: a neutral to dark gray under a dark blend, tan under a blend that is mostly brown, and not a base that strongly contrasts with the chips. When a blend holds many colors with no clear leader, it leaves the choice to taste.
Light blends catch people out. Torginol highly recommends a light base, white or a very light gray, under blends made mostly of white or light gray chips, and shows a bright blend over a gray base looking duller, its accent colors losing their pop. On a partial broadcast the base color carries even more weight, because it covers more of the floor than the chips do.
Sun at the garage door: fading chips, yellowing coats
Sunlight works on two layers of a flake floor. Torginol rates its flake colors for lightfastness after 1,000 hours of xenon-arc light exposure under ASTM G155, and does not recommend its poorly rated colors where a floor gets direct sun. The poor ratings fall on bright colors such as Primary Yellow and Primary Blue and on its fluorescent shades, while White, Black, Charcoal and Medium Gray are rated good. For outdoor floors it sells a UV+ flake line and advises pairing it with a UV-stable topcoat.
The clear coat over the chips matters as much as the chips. Sherwin-Williams' data sheet for its ArmorSeal 1000 HS floor epoxy states that epoxy coatings may darken or yellow following application and curing, a change easiest to see over white and light gray blends. Laticrete's data sheet for the low gloss version of its Spartacote Flex XPL polyaspartic topcoat lists it as UV stable and says it reaches its final low gloss 24 to 48 hours after it goes down. Working times and humidity limits for a polyaspartic topcoat over flake are on a page of their own.
Checks to make before the blend is ordered
A color on a screen or a printed card is not the floor. Laticrete's chip color card says its colors are representative only and that mock-ups and field test areas are needed to confirm color and appearance. A few checks close the gap between the card and the garage:
- Ask for a sample board made with the actual base coat, chips and clear topcoat, not loose chips in a bag.
- Look at the sample under the garage's own lights, then again in daylight with the door open.
- Set the sample beside an oil stain or a patched crack to judge how much the blend will hide.
- On a large floor, mix boxes from different lots before the broadcast: Torginol says its variegated and marble flakes can vary slightly from lot to lot and advises mixing lots before use.
- If the door faces strong afternoon sun, check each chip color's lightfastness rating before settling on a blend.
Need a hand?
Planning a flake floor in Huntington? Send the garage's size and photos of the blends you like, and ask to see a sample made with the base and topcoat you would get.
More from the blog
Quick Answers
What is the most popular flake size for a garage floor?
Torginol, a flake maker, names 1/4 inch its most popular size. Smaller chips give a finer, more even, stone-like look and can take more flake for full coverage: Torginol's chart gives 5 to 7 square feet per pound for 1/4 and 1/8 inch chips but 3 to 5 square feet per pound for 1/16 inch, and Laticrete's gives 4 to 6 for its 1/8 inch chip.
Will flake colors fade in a sunny garage?
Some can. Torginol rates each flake color for lightfastness after accelerated UV testing and does not recommend its poorly rated colors, such as Primary Yellow, Primary Blue and its fluorescent shades, for floors in direct sun. Its whites, blacks and most grays rate good. The topcoat matters too: epoxy coatings may darken or yellow once cured, while UV-stable polyaspartic topcoats are sold for floors that see sun.
Does the base coat color matter if the chips cover the whole floor?
Yes. Torginol notes that even a full broadcast leaves small gaps where the base coat shows through, which shifts the overall color of the floor. Its rule is a base similar in color and tone to the blend's main color, such as gray under a dark blend or tan under a brown one, and a white or very light gray base under light blends.